------------------------------------------------------------------------------------------------------------- Use -managed_mode= option to narrow down the help. ------------------------------------------------------------------------------------------------------------- Part Utility with -managed_mode=yes options are: ------------------------------------------------------------------------------------------------------------- Login Options: -------------- -u[ser]= To specify Teamcenter user name -g[roup]= To specify Teamcenter group name -p[assword] To specify Teamcenter password -pf= File to specify the Teamcenter password Input Part Options: ------------------- -part= Specification of single part to process. Part name should be in the @DB/ / format, where Part Identifier is fnd0partIdentifier property on Item -i[nput_list]= List of specifications of input parts. Part name should be in the @DB// format, where Part Identifier is fnd0partIdentifier property on Item -f[older]= Name of folder listing input parts -folder_user= Name of user whose folder to use -resume Line number of input list to start processing from Functional Options: ------------------- -d[rawings]= Update drawings -structure_sync Synchronize structures between NX and Teamcenter. Default = -transforms_source Source of transforms if different from -structure_sync argument.Default = -sync_arrangements= Synchronize arrangement data if consistent with other structure sync settings.Default -cleanu[p]= Perform part cleanup before operation. Default -anon[ymize]= Removes user and program version strings from part history. Default -force_read_jt Force to read from a JT dataset even if a master dataset exists -convert_mcs= Convert mating conditions to assembly constraints and output report -regen_lw Force all lightweight bodies in the specified part to be regenerated. By default the faceting parameters previously used to create each body will be used again.This option is now being done by default for parts saved before NX7.5. -regen_lw_def_tol Similar to regen_lw however this flag will not use the faceting parameters on the existing body but the default faceting parameters will be utilized instead. -remap_drawing_callouts Remap the callout references in drawing to = -synchronize_callout_to_teamcenter= Update the Find No.in Teamcenter based on the CALLOUT value on the NX part occurrences -convert_units_to_mm Convert the part from inches to millimeters -convert_units_to_in Convert the part from millimeters to inches -convert_line_widths Converts all legacy line width in the specified parts to use new line widths. Conversion is done based on the Legacy Line Width Conversion part preference. -recreate[_missing_stock_components] For Routing assemblies, re-creates any missing stock as component components -create_drawing_snapshot Creates snapshot data of the part for its drawings -generate_trueshape= Generate True Shape occupancy data. Default -record_part_data= Record part data (bounding box & mass properties as well as properties to allow Active Workspace to filter search results based on part / assembly / drawing, interpart links, product interfaces, user defined features, reference components, suppressed components, constraints, arrangements, geometry overrides, position overrides, and parts list).Default -record_altrep_notes= Record AltRep occurrence notes. Default -update_matl_specification= Updates the material specification table associated with UGMASTER or UGALTREP without changing the last modified date. Default -h[elp] Produces this message Add-On Options: --------------- -non[_masters]= Automatically process non-master parts.Default -bypass= Use bypass privilege if necessary. Default -update_mod[_props]= Update last modifying user/date on dataset -k[eep_volume]= Use original volume for output parts. Default -set_new_dataset_o[wner] Sets the ownership of new datasets to be either that of the owning item - rev or multi - CAD jt dataset -allow_released= Process parts with release status. Default -force_structure_sync= Force synchronize structures as requested by - structure_sync.Default -allow_null_transform Used with -structure_sync used with -structure_sync=from_teamcenter and -transforms_source = from_teamcenter to allow transforms from Teamcenter to be null -read_mapped_attri[butes]= Read mapped attributes if consistent with other structure sync settings.Default -compression= Compresses|uncompresses the part(s) -y Fully load components that are not at the current version of NX -force_operate Used with the -y switch to force all components to be operated on -mc_parts_only Used in conjunction with convert_mcs to specify only convert parts which contain mating conditions -mc_dry_run Used in conjunction with convert_mcs to do the mating condition conversion and generate the conversion report without saving any parts. -mc_dont_load_referenced_geometry Used in conjunction with convert_mcs to not load geometry referenced by the mating conditions being converted. Note this will bypass constraint conversion checking. -debug= Print debug information. Default -use_default_load_option_file Uses specified default load options. This cannot be used along with - y option, -y option takes precedence if set -specified_non_master_only Used with -input_list option to process Only specified non - master while processing the non - master parts from the input list -env Specify customer environment -out[put_file]= File to write failure information to -log[_file]= File to write log information to in case of failure ------------------------------------------------------------------------------------------------------------- Part Utility with -managed_mode=no options are: ------------------------------------------------------------------------------------------------------------- Input Part Options: ------------------- Processes file . -d Convert all parts/UDFs in current directory. -d Convert all parts/UDFs in directory . Functional Options: ------------------- -u Processes UDF files. -uo Processes UDF files only. -uc Uncompresses the part(s) when processing. -co Compresses the part(s) when processing. -us Updates the assembly structure to include any changes in lower level sub-assemblies. -dwg_update Force update all drawings without any fixup. -cleanup Perform part cleanup. -anonymize Removes user and program version strings from part history. -convert_mcs Converts mating conditions to assembly constraints. Logs a constraint conversion report to . -ts Generates True Shape data only. -regen_lw Force all lightweight bodies in the specified part to be regenerated. The faceting parameters previously used to create each body will be used again. Note: For assembly level representations the regeneration operation will be executed only if the source component parts are loaded. The -y switch can be used to ensure the components are loaded. This option is now done by default for parts saved prior to NX7.5. -regen_lw_def_tol Same as -regen_lw except that with this option the faceting parameters on the existing body will be ignored and the default system or user specified (if defined in the customer defaults) faceting parameters will be utilized. -convert_line_widths Converts all legacy line width in the specified parts to use new line widths. Conversion is done based on the Legacy Line Width Conversion part preference. -create_drawing_snapshot Creates snapshot data of the part for its drawings. -[h]elp Prints the help message and usage details. -recreate_missing_stock_components For Routing assemblies this option will re-create any missing stock as component components. Add-On Options: --------------- -c Creates components if necessary during upgrade. -r Prints part_utility (NX) release. -s Traverses subdirectories. -nop Do not change file owner and protection. -ndates Do not change file modified date and accessed date. -y Fully load assembly, and processes components that are not at the current version of NX. -f Used with the -y switch to force all components to be processed. -mc_parts_only Used in conjunction with convert_mcs to specify only parts which contain mating conditions. -mc_dry_run Used in conjunction with convert_mcs to do the mating condition conversion and generate the conversion report without saving any parts. -mc_dont_load_referenced_geometry Used in conjunction with convert_mcs to not load geometry referenced by the mating conditions being converted. Note this will bypass constraint conversion checking. -l Logs a short report to the syslog. -l Logs a short report to the syslog and . -ll Logs an extended report to the syslog. -ll Logs an extended report to the syslog and . -o Sets new file as the destination. -o Sets existing directory as the destination.